Features of manufactured and impact failure of a layered material based on Ti-6Al-4V alloy

Received 10 June 2020; Accepted 23 July 2020;
This paper is written in Russian
Citation: A.A. Sarkeeva. Features of manufactured and impact failure of a layered material based on Ti-6Al-4V alloy. Lett. Mater., 2020, 10(3) 345-350
BibTex   https://doi.org/10.22226/2410-3535-2020-3-345-350

Abstract

Impact loading diagrams of layered samplesStructural methods for controlling the properties of a layered material (LM) based on Ti-6Al-4V alloy are presented in this work. The layered materials were manufactured by diffusion bonding. They consist of seven and thirteen sheets of the thickness about 1.5 and 0.8 mm, respectively. Two methods of assembling the sheets were used: in one case, they were stacked relative to each other so that the rolling direction (RD) in them coincided (LM of type 1), and in the other, they did not match (LM of type 2), the angle between the RD in the neighboring sheets was 0 and 90 degrees, respectively. It was found that the prismatic texture (texture with datum planes oriented perpendicular to the rolling plane) present in the as-received sheets is inherited by the layered material of type 1 that it causes the anisotropy of impact strength. Almost the same distribution of the pole density of basis in the rolling direction and in the transverse direction determines the isotropy of impact strength in the layered material of type 2. A comparative evaluation of the test results has shown that when the crack propagates simultaneously through all layers (the crack divider orientation) the impact strength value is higher for the 7‑layer material when the crack propagates sequentially from one layer to another (the crack arrester orientation) it is higher for the 13‑layer material. The quantitative assessment of the fracture characteristics made it possible to establish that the decrease in the impact strength of the samples tested in the crack divider orientation with the number of layers increasing is conditioned by decreasing both the crack initiation energy and the crack propagation energy. In contrast, the improvement of impact strength of the samples tested in the crack arrester orientation occurs due to the significant increasing the crack propagation energy at an insignificant decreasing the crack initiation energy.

References (24)

1. Titanium and Titanium Alloys: Fundamentals and Applications. 1rd edn (ed. by C. Leyens, M. Peters). Weinheim, Wiley-VCH (2003) 523 p. Crossref. Crossref
2. R. V. Safiullin, R. M. Galeyev, O. R. Valiakhmetov et al. Lett. Mater. 6 (4), 281 (2016). (in Russian) [А. Р. Сафиуллин, Р. М. Галеев, О. Р. Валиахметов и др. Письма о материалах. 6 (4), 281 (2016).]. Crossref
3. R. V. Safiullin, M. H. Muhametrahimov, S. P. Malycheva et al. Lett. Mater. 8 (3), 329 (2018). (in Russian) [Р. В. Сафиуллин, М. Х. Мухаметрахимов, С. П. Малышева и др. Письма о материалах. 8 (3), 329 (2018).]. Crossref
4. H.-S. Lee. In: Welding and Joining of Aerospace Materials (ed. by M. C. Chaturvedi). Sawston, Woodhead Publishing Limited (2012) p. 320.
5. E. Yakushina, A. Reshetov, I. Semenova et al. Materials Science and Engineering: A. 726, 251 (2018). Crossref
6. F. A. Calvo, J. M. Gómez De Salazar et al. J. Mater. Sci. 27, 391 (1992). Crossref
7. R. Ya. Lutfullin. Lett. Mater. 1 (1), 59 (2011). (in Russian) [Р. Я. Лутфуллин. Письма о материалах. 1 (1), 59 (2011).]. Crossref
8. X. He, Y. Dong, Y. Li, X. Wang. Int. J. Fatig. 106, 1 (2018). Crossref
9. A. A. Sarkeeva, A. A. Kruglov, R. Ya. Lutfullin et al. Composites Part B. 187, 107838 (2020). Crossref
10. A. A. Ganeeva, A. A. Kruglov, R. Y. Lutfullin. Rev. Adv. Mater. Sci. 25, 136 (2010).
11. P. G. Miklyaev, Ya. B. Fridman. Anisotropy of mechanical properties of metals. Moscow, Metallurgy (1986) 224 p. (in Russian) [П. Г. Микляев, Я. Б. Фридман. Анизотропия механических свойств металлов. 2-е изд. Москва, Металлургия (1986) 224 с.].
12. M. R. Bache, W. J. Evans. Mater. Sci. Eng. A. 319 - 321, 409 (2001). Crossref
13. S. Ya. Betsofen, A. A. Ilyin, S. V. Skvortsova et al. Metally. 2, 54 (2005). (in Russian) [С. Я. Бецофен, А. А. Ильин, С. В. Скворцова и др. Металлы. 2, 54 (2005).].
14. S. Ya. Betsofen, A. A. Ilyin, V. V. Plikhunov et al. Metally. 5, 51 (2007). (in Russian) [С. Я. Бецофен, А. А. Ильин, В. В. Плихунов и др. Металлы. 5, 51 (2007).
15. Patent RF № 2380185, 27.01.2010. (in Russian) [Патент РФ № 2380185, 27.01.2010.].
16. A. I. Horev. Svarochnoe proizvodstvo. 10, 11 (2012). (in Russian) [А. И. Хорев. Сварочное производство. 10, 11 (2012).].
17. A. I. Horev. Tekhnologiya legkih splavov. 4, 92 (2002). (in Russian) [А. И. Хорев. Технология легких сплавов. 4, 92 (2002).].
18. J. D. Embury, N. J. Petch, A. E. Wraith et al. AIME MET SOC TRANS. 239 (1), 114 (1967).
19. M. Georgiev. Impact Crack-Resisting of Metals. Sofia, Bulvest 2000 (2007) 231 p. (in Bulgarian) [М. Георгиев. Пукнатиноустойчивост на металите при ударно натоварване. Софии, БУЛВЕСТ. 2000 (2007) 231 с.].
20. M. M. Borodkina, E. N. Spektor. X-ray analysis of the texture of metals and alloys. Moscow, Metallurgy (1981) 272 p. (in Russian) [М. М. Бородкина, Э. Н. Спектор. Рентгенографический анализ текстуры металлов и сплавов. Москва, Металлургия (1981) 272 с.].
21. A. A. Ganeeva, A. A. Kruglov, R. Y. Lutfullin. Deformaciya i razrushenie materialov. 7, 38 (2011). (in Russian) [А. A. Ганеева, А. А. Круглов, Р. Я. Лутфуллин. ДиРМ. 7, 38 (2011).].
22. G. I. Pogodin-Alekseev. Dynamic strength and brittleness of metals. Moscow, Mechanical Engineering (1966) 242 p. (in Russian) [Г. И. Погодин-Алексеев. Динамическая прочность и хрупкость металлов. Москва, Машиностроение (1966) 242 с.].
23. D. V. Vlasova, A. I. Plokhikh, A. A. Minakov. Novye materialy i tekhnologii v mashinostroenii. 27, 9 (2018). (in Russian) [Д. В. Власова, А. И. Плохих, А. А. Минаков. Новые материалы и технологии в машиностроении. 27, 9 (2018).].
24. K. Hellan. Introduction to fracture mechanics (translate from English A. S. Kravchuk; ed. by E. M. Morozov). Moscow, Mir (1988) 364 p. (in Russian) [К. Хеллан. Введение в механику разрушения (пер. с англ. А. С. Кравчука; под ред. Е. М. Морозова). Москва, Мир (1988) 364 с.].

Similar papers

Funding

1. state assignment of IMSP RAS - № АААА-А17 117041310221 5